Inflates a road tire to up to 95 PSI for tubulars and up to 90 PSI for clinchers. Inflates mountain tires to 40 PSI. Contains a sealant which fixes small punctures. Presta or Schrader compatible. 16 cm long and 32 mm wide. 80 grams.
***Ground Shipping Only***
B-Stock - This product has one or more B-Stock units available. These units can be purchased at a discount (see option select). B-Stock units were returned from other customers and may have missing or damaged packaging materials. These units are otherwise as new. The full manufacturer warranty applies. Click Here for more information.
The product weight specified is an approximate weight based on the manufacturer's specifications (if available) or our measurement of one or two examples. For most products, the weight will typically vary by 5% to 10%.
Weight: 80 grams
Mfg PartNum: 1315PR0175555BX
I run tubeless tires, so I always carry a pressurized sealant cartridge. I used to carry the Hutchinson sealant (Fast'Air). However, I was in Kalispell MT, and needed a cartridge, as I did not have any Hutchinson. I went to a local bike shop, and asked for the Hutchinson product, but they did not have it. However, they said, "try this", showing me the Vittoria. So, I bought 2, and have not been disappointed. The main thing I like is ease of use - compared to the Hutchison sealant cartridge, the Vittoria is much easier to use, as the nozzle fits directly on the Presta valve, unlike the Rude Goldberg (sorry I am dating myself) setup of the Hutchison cartridge. BTD carries both, but I would suggest going w/ the Vittoria.
Good product for punctures and cuts less than 1 mm (As it claims?). Works better on round punctures compare to cuts.
Borderline between 1-2 mm.
Cuts 2mm or more than 2 mm there is less chance. It will seal 2 mm cut first but when you pump the tire the clot can't hold up after 60-70 PSI on road tire. The clot will pop out followed by squirting whatever you injected in.
It is designed for 2 tires but You may end up injecting 70-80% of the can on one tire. Will you reply on 20% left over for next use?
You will need to use your Co2 on top of Vittoria sealant because the pressure is not high enough.
I have tried stan also. To me they both are in same level/strenght except stan is alot cheaper. Stan couldn't seal the cut more than 2 mm either but it worked for smaller size same as Vittoria
I valued the product low, simply because you are paying 5-10 times more compare to stan but you gain no advantage. This is my opinion. Decision is yours
I've used half a dozen of these over the years. They'll seal small holes and get you going quickly without a laborious and time consuming tire change. If you're on regular tubed clinchers, it's too much to spend for the convenience without the assurance of a successful seal-maybe in a race. Have a plan B-a spare tub and a regular inflator in case the sealant fails.
I rode to work today, noticing that there was a lot of glass on various parts of the road. Got to work fine at 8am. At noon, I checked the bike and saw that my rear tire was flat. Brought out the Pit Stop, rotated the valve to 12 o'clock and gave it a shot. Fixed it instantly! Topped it off with a litte CO2. Now in the next four hours, I can make sure it holds before riding home.
A little pricy, but compared to replacing a tubular tire...worth every penny.
Running Vittoria Pave Evo CG tubulars on CX tubular wheels. Beautiful ride!
Carrying an extra tire is a pain when a small canister usually will do the trick. I ride Cont. Competition tubulars and when needed this stuff works.
We ride tough tubulars on racing bikes as West Texas is tough for flats. Although the pit stop may need to sit a day or two it usually seals spot punctures, saving purchase of a sewup. Our rims are 95mm so this is the only possible fix. I have heard people routinely start with this in sewups for prevention. Directions are simple- start with stem up top then be sure to rotate at intervals and dont leave stem at bottom for awhile. Get more air in soon.
I ride tubulars, it works about 30 percent of the time (maybe). It's $15 per can and I can call my wife for a ride or Uber home for $15 to $20 where I live. The only good thing about this stuff (crap) is that it gives you the hope that you can limp home in the event of a flat. Stans works far better. So, if it gives you peace of mind to know you have something that might get you out of a jam, great - but after using it +15 times and having mediocre at best results I don't feel that way anymore. Oh, and when it doesn't work and spits latex all over your rear triangle, have fun cleaning it (note, clean it as soon as you get home b/c once dried it's a bear to remove.
I ride tubbies and this stuff has gotten me home numerous times. Easier than putting on my spare tire it had worked on some pretty large punctures. I don't even need to use an entire can to seal a puncture. The thing is, it is not cheap but when I am miles from home riding solo I'd pay double to be able to limp home and not have to, on the side of the road, pull off an old tubular and then put the spare on (and still have to limp home).
Can't live home without Vittoria pit stop if you like tubular tires, works very well and easy to use pump your tire right away without losing to much time and less to carry don't need spare. Downside if you have a blowout or huge cut it will not seal it.
Riding tubular tires should be experienced by every cyclist at least once. I love riding my tubies, thus carrying this sealant is a must! Yes, it is a little expensive, but unlike other products IT WORKS, and that's nothing compared to your $100 tubular tire, which is rendered useless, unless you can seal that puncture, especially 60 miles away from home. Yes, you can carry a spare pre-glued tubular in your pocket, but who wants to go through the trouble of removing and mounting a new one in the middle of nowhere. Just make sure that you remove the puncture debris prior to using it.
Articles will open in new tab.